Comprehensive numerical investigations on the thermal performance of heat recirculating micro combustor with pin fins for micro-thermal voltaic system applications

Aiming at improving the relatively low energy output and energy conversion efficiency of the micro-thermal voltaic (MTPV) system, an innovative heat recirculating micro combustor with pin fins is designed. The effects of pin fins arrangement, hydrogen/air equivalent ratio on the energy output and performance of CHMC, HMCP and HMCI are compared and investigated. The result shows that when the V_in is 6 m/s and Φ is 1.0, the emitter power of CHMC is 72.76W, and that of HCMP and HCMI micro combustor are 75.99W and 76.35W. and the emitter efficiency of CHMC, HCMP and HCMI is 41.93%, 43.26% and 44.01%. HMCI has better energy output capability compared with CHMC and HMCP. Even though, HMCI brings a higher pressure drop, it is within the acceptable range. When the V_in is 6 m/s, the pressure drop from the pin fins only accounts for 26.4% of the total pressure drop for HMCI. Through the study of equivalent ratio, it is found that HMCI has good adaptability in different equivalent ratio range. This work provides new ideas for the development of MTPV system in the future.     

煤矿水仓清理新工艺

通过调研现场情况以及检测煤泥特性，探寻一种实用性强、方法简单的新工艺来替代劳累的人工和繁琐的机械清淤，解决现实问题。针对实际情况开发清仓新工艺，介绍了该工艺的技术路线选择、设计依据以及实际应用效果。该新工艺具有降低清仓时间、减轻工人劳动强度、设备操作简单、实用性强等特点。     

Experimental research on micro hole drilling of polycrystalline Nd:YAG

Polycrystalline Nd:YAG materials have wide applications in solid-state lasers. In this study, micro hole drilling experiments were performed on polycrystalline Nd:YAG using a polycrystalline diamond micro drill. The hole diameter, edge chipping, and hole wall surface quality were examined in detail. The results showed that the hole diameter was slightly larger than tool diameter. A diameter error of less than 5.5% was achieved. The edge chipping at the entry hole was formed by the encircled petal shape exfoliations, which were produced by the indentation and rotation movement in the drilling entry stage. Edge chipping at the exit hole was generated by an entire piece of exfoliation, which was produced by a circle of microcracks around the tool tip propagating to the bottom surface in the drilling exit stage. The edge chipping width at the entry hole was smaller than that at the exit hole. Based on different material removal modes, the hole surface morphology was classified into three types: ductile removal, coexisting ductile and brittle removal, and brittle removal. The hole surface quality mainly depended on the proportion of the brittle fracture to ductile removal surface.     

车用有机朗肯循环系统中计量泵的性能研究

在模拟车用有机朗肯循环(organic Rankine cycle,ORC)系统的工作环境下,设计并搭建以R123作为工质的液压隔膜计量泵性能测试平台。在额定转速(2900 r/min)下,通过调节液压隔膜计量泵的冲程(25%、50%、75%、100%)和出口压力,得到变工况下液压隔膜计量泵的特性曲线,并分析液压隔膜计量泵的关键参数对车用ORC系统性能的影响情况。结果表明:液压隔膜计量泵的流量受冲程影响,与出口压力基本无关。其输入功率和实际运行效率均随着冲程的增加而升高,最高分别可达523.91 W、88.27%。应用该液压隔膜计量泵的模拟车用ORC系统吸热量变化范围较广,系统热效率最高可达12.81%。液压隔膜计量泵可应用于车用ORC系统,通过调节液压隔膜计量泵的冲程和出口压力,可实现提高车用ORC系统热效率、增加系统净输出功率的目的。     

汽蚀对离心泵性能影响的实验研究

离心泵长时间运转后,会出现危害严重的汽蚀现象,造成泵性能下降,严重时影响泵的效率、寿命,甚至造成离心泵内部部件损坏。文章通过改变进口压力的方法对单泵、双泵并联、双泵串联等工况下汽蚀对离心泵性能影响进行实验研究。结果表明:当进口压力小于输送液体的饱和蒸汽压时,液体开始发生气化并伴随气泡产生,表明泵内发生汽蚀;汽蚀初期离心泵的效率开始下降,但表现不明显;随着汽蚀不断增大至严重汽蚀区时,Q 1~η曲线出现陡坡,效率出现明显下降并伴随嗡响。实验证明采用提高泵的进口压力等措施可适当减小汽蚀对泵性能的不利影响。     

水泵水轮机导叶动态水力矩特性分析

采用SST k-ω湍流模型对某高水头水泵水轮机进行全流道三维非定常数值模拟,分别对在水轮机工况和水泵工况运行下的导叶动态力矩特性进行分析。结果表明:在水轮机工况下,随着流量的增大,不同位置处导叶的动态水力矩变化规律一致,力矩值由正值变为负值,力矩脉动频率与转轮叶片数相关,流量越大,叶频影响越显著;在水泵工况下,最高扬程工况时导叶水力矩脉动频率主频为转频且脉动幅值较大,而最低扬程工况下导叶水力矩脉动主频为叶频,力矩脉动幅值较小。     

甲基氯硅烷精馏流程的模拟与优化

采用Aspen plus软件对工业七塔精馏过程进行全流程建模与模拟，优化工艺参数，研究了新的精馏节能工艺。对一甲塔等7个精馏塔采用双因素水平的灵敏度分析，考察了塔釜采出率、回流比、进料位置和塔顶压力对产品浓度和热负荷的影响，确定一甲塔最优的工艺参数：塔釜摩尔采出率为0.92，摩尔回流比为130，塔顶压力为0.18 MPa，总理论板数为400，在210块理论板位置进料。在此基础上，针对高能耗的脱高塔/脱低塔，模拟研究了双效精馏新工艺，新工艺可节省39.70%的年总成本；针对一甲塔模拟研究了热泵精馏新工艺，新工艺可降低41.42%的年总成本。     

抽油井不压井作业装置及抽油泵底阀设计

江苏油田的部分油井存在油管短路、地层高压低渗、漏失严重等问题,这些问题造成压井作业困难,并且压井作业过程中的井控与环境污染风险较大。为了进行不压井检泵作业,同时缩短检泵之后的产量恢复周期,进行了不压井作业技术研究,并研制了不压井作业装置。为解决起下抽油杆过程中的防喷问题,改进了抽油泵底阀结构,该结构可实现起下抽油杆过程中油管不带压、无溢流,并保障起下油管过程中的井控安全。该技术在江苏油田现场应用9井次,效果良好。     

烟气CO2捕集热能梯级利用节能工艺耦合优化

醇胺法捕集CO₂技术是一种较成熟的CO₂捕集技术，具有吸收速度快、脱除效果好等显著优点，但其操作费用高、解吸能耗大。本文以降低醇胺法捕集烟气中CO₂系统再生能耗为出发点，对常规醇胺法捕集CO₂工艺统进行了节能优化研究。在常规工艺流程基础上引入压缩式热泵节能技术，并利用Aspen Plus软件建立了基于压缩式热泵技术的CO₂捕集工艺流程模型。研究了压缩式热泵与机械蒸汽压缩回收（MVR）热泵、分流解吸、分布式换热、级间冷却4种节能工艺耦合，通过模拟计算与优化，结果说明了最佳节能工艺组合为“解吸塔压缩式热泵+贫液MVR热泵+分流解吸+级间冷却”耦合的CO₂捕集工艺流程，当解吸塔顶气体分流比为0.25∶0.75、冷富液分流比为0.05∶0.95、级间冷却器位于吸收塔17块塔板位置、吸收塔输入冷量为-3.0GJ/h时，系统再生能耗最低，为2.533 GJ/tCO₂，相比常规有机胺工艺（再生能耗4.204GJ/tCO₂）节能率39.748%。     

环形通道内液态铅铋合金流动换热特性实验研究

通过对环形通道内液态铅铋合金的流动换热特性进行实验研究，得到了气泡泵注气对液态金属流动的影响，并拟合出环形通道内液态铅铋合金的摩擦系数关系式和换热特性关系式。结果表明：采用气泡泵注气能有效提升铅铋合金的质量流速；相同Reynolds数下环形通道内液态铅铋合金的摩擦系数大于由布拉休斯公式计算得到的摩擦系数；液态铅铋合金对流换热过程中，导热项占主导地位，并且Nusselt数随Peclet数的增大而增大。